Turbo Speed Sensor Kit
Turbo Speed Sensor Kit for Garrett and BorgWarner turbochargers. Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map.
Install Effort
Turbo Speed Sensor Kit for Garrett and BorgWarner turbochargers. Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map.
The Turbo Speed Sensor Kit is Critical for Proper Engine Operation
Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map. Traditionally, installing these sensors was difficult for the end-user—requiring complex machining at a compound angle to carefully hit the contour area of the wheel bore at the right angle. The latest generation BorgWarner and Garrett G turbos have this precision machining already done to every compressor cover.
Note: We strongly recommend connecting this sensor to our Turbo Speed Gauge!
Speed Sensor Kit Includes
- (1) Speed sensor, the frequency output
- (1) Speed sensor hold-down bolt
Notes for Installation
- Garrett's turbos are plug-and-play without drilling
- BorgWarner requires additional steps for installation
BorgWarner Installation Procedure
A 1/4″ Drill bit is all that's needed and the length/depth is very short. This hole allows the top of the sensor to come flush with the contour surface. The hole does not have to be precise as no sealing takes place in the small hole that the user just created. The hole must be deburred where it pierces into the wheel bore. The goal is to make sure that there are no sharp edges remaining in the wheel bore that the compressor can become caught on. The speed sensor is powered by a +5V supply and the return signal is a variable frequency square wave that has a maximum amplitude of 5V and has a 50% duty cycle.
-
- 1. Remove compressor cover from turbo (CAREFULLY)
- 2. Place cover on a table, with some kind of backing so that it won’t slide while being drilled
- 3. Equip a hand drill with a 1/4” drill bit
- 4. Drill out the bottom of the speed sensor bore while being careful not to nick the side walls of the bore where the speed sensor o-ring will seal.
- 5. De-burr the hole where it protruded into the compressor wheel region.
- 6. Lubricate the speed sensor o-ring
- 7. Install the speed sensor into the bore and check for a good fit.
- 8. Use a file on the mounting surface if the sensor needs to protrude further into the bore. The sensor tip should be nearly flush (within 0.5mm) with the edge of the hole.
- 9. Tighten the speed sensor hold-down bolt.
- 10. Re-install compressor cover on turbo and verify that the compressor wheel spins freely.
Click HERE to view a downloadable PDF file of how to install the Speed Sensor. If you have any questions about this product or its installation, contact us.
SKU
179430
WEIGHT
1.000000
BRAND
Full Race
Universal Installation Parts

Large GT/GTX Oil Drain Flange

T4 Open Turbine Flange

T3 T4 Oil Feed Flange

T4 Divided Turbine Flange

4 Bolt Downpipe Turbine Flange For GT, GTX and T3/T4 Garrett Turbos

2.5" Silicone Hump Hose

Full-Race T4 Divided 5 Layer Inconel Gasket

2.5" 45 Degree Coupler Extra Long

3.0" 3-Bolt Exhaust Flange for Downpipe and Exhaust Connections

Full-Race 304 Stainless Steel 3" V-Band Flange Kit

T3 Turbine Flange Gasket

Full-Race Billet Vacuum / Boost Reference Manifold Block

4" V-band Flange Kit

T3 Open Turbine Flange

10mm M10 Inconel Turbo Stud Hardware Kit T3 T4 Turbos

Full-Race Billet Medium GT Oil Drain Flange (1/2" NPT)

Full-Race 304 Stainless Steel 4" V-band Flanges

Silicone 4" 45 Degree Intake Elbow / Coupler
similar products

3 Port MAC Boost Control Solenoid (BCS)

Injector Dynamics ID1300X Injectors

Injector Dynamics ID2600 Fuel Injectors

Injector Dynamics USCAR to OBD2 Honda Plug n' Play K Series Injector Clip (RSX, Accord, 8th Gen Civic Si)

Walbro 450 LPH E85 Compatible Walbro Universal In-Tank Fuel Pump

Walbro 255LPH E85 compatible High Pressure Fuel Pump

Precision PTE PT6466 GEN2 64mm Turbo

4 Port MAC Boost Control Solenoid Mount for EFR Turbochargers

BorgWarner Airwerks S372SX-E - 72mm Enhanced S300SX-E 9180 Turbo

BorgWarner Airwerks S362SX-E

Injector Dynamics ID1700X Injectors

Full Race 4 Port MAC Boost Control Solenoid
For SHOP OWNERs
& KIT BUILDERs
Full-Race Motorsports is the most
trusted name in turbocharging.