Turbo Speed Sensor Kit
Turbo Speed Sensor Kit for Garrett and BorgWarner turbochargers. Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map.
Install Effort
Turbo Speed Sensor Kit for Garrett and BorgWarner turbochargers. Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map.
The Turbo Speed Sensor Kit is Critical for Proper Engine Operation
Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map. Traditionally, installing these sensors was difficult for the end-user—requiring complex machining at a compound angle to carefully hit the contour area of the wheel bore at the right angle. The latest generation BorgWarner and Garrett G turbos have this precision machining already done to every compressor cover.
Note: We strongly recommend connecting this sensor to our Turbo Speed Gauge!
Speed Sensor Kit Includes
- (1) Speed sensor, the frequency output
- (1) Speed sensor hold-down bolt
Notes for Installation
- Garrett's turbos are plug-and-play without drilling
- BorgWarner requires additional steps for installation
BorgWarner Installation Procedure
A 1/4″ Drill bit is all that's needed and the length/depth is very short. This hole allows the top of the sensor to come flush with the contour surface. The hole does not have to be precise as no sealing takes place in the small hole that the user just created. The hole must be deburred where it pierces into the wheel bore. The goal is to make sure that there are no sharp edges remaining in the wheel bore that the compressor can become caught on. The speed sensor is powered by a +5V supply and the return signal is a variable frequency square wave that has a maximum amplitude of 5V and has a 50% duty cycle.
-
- 1. Remove compressor cover from turbo (CAREFULLY)
- 2. Place cover on a table, with some kind of backing so that it won’t slide while being drilled
- 3. Equip a hand drill with a 1/4” drill bit
- 4. Drill out the bottom of the speed sensor bore while being careful not to nick the side walls of the bore where the speed sensor o-ring will seal.
- 5. De-burr the hole where it protruded into the compressor wheel region.
- 6. Lubricate the speed sensor o-ring
- 7. Install the speed sensor into the bore and check for a good fit.
- 8. Use a file on the mounting surface if the sensor needs to protrude further into the bore. The sensor tip should be nearly flush (within 0.5mm) with the edge of the hole.
- 9. Tighten the speed sensor hold-down bolt.
- 10. Re-install compressor cover on turbo and verify that the compressor wheel spins freely.
Click HERE to view a downloadable PDF file of how to install the Speed Sensor. If you have any questions about this product or its installation, contact us.
SKU
179430
WEIGHT
1.000000
BRAND
Full Race
similar products

BorgWarner Airwerks S257SX-E - 57mm Enhanced S200SX-E 7670 Turbo

Barb Fittings and Breather Filter for 4 Port Boost Control Solenoid

Honda / Acura K-Series Intercooler Charge Pipes

Full Race Turbo Blankets For T3 Turbochargers

Walbro 525 LPH F90000285 E85 Hellcat Fuel Pump

BorgWarner EFR 7670 Turbo

Walbro 255LPH E85 compatible High Pressure Fuel Pump

Full Race 4 Port MAC Boost Control Solenoid

Walbro 450 LPH E85 Compatible Walbro Universal In-Tank Fuel Pump

Injector Dynamics ID1700X Injectors

Injector Dynamics ID1050X Injectors

Hondata Map Sensors (4 Bar or 7 Bar Options)
For SHOP OWNERs
& KIT BUILDERs
Full-Race Motorsports is the most
trusted name in turbocharging.