Injector Dynamics ID1300X Injectors
Injector Dynamics ID1300X Injector (Injectors Priced Individually)
Injector Dynamics ID1300X Injector (Injectors Priced Individually)
Injector Dynamics ID1300X Injector
**Please do NOT purchase single or partial quantity replacement injectors for an existing set, as they will not be flow matched and can cause drivibility issues or damage your engine. If you think an injector needs to be replaced, you must first follow this cleaining procedure through ID for your existing injector set, found here - https://injectordynamics.com/
Nominal Flow Rate – 1335cc/min @ 3.0 Bar (43.5 psi) Using Iso Octane at 52 Degrees C (125 Degrees F)
Maximum Differential Fuel Pressure – 7.0 Bar (101.5 psi)
Fuel Compatibility – Compatible With All Known Fuels – (Designed Specifically for Alternative Fuels)
Electrical Connector – USCAR
**Note: The Last Digit on the ID Part Number is your Quantity of this Injector Type. ie. Audi VR6 (12 valve) #1300.60.14.14.6 = 6 Injectors, Totaling $1350.00**
About The Injector Dynamics X-Series Injectors
With the ID1300x and ID1700x setting the current standard for high flow injectors, and the recent release of the ID1050x, many are asking what makes these injectors perform at such high levels. The simple answer is intent. It is no surprise that an R-Compound tire designed for track use will outperform a standard street tire, even if both come from the same manufacturer. The same can be said for the performance of the ID1050x, ID1300x and ID1700x, which are designed specifically for motorsport use.
The partnership of Injector Dynamics and Bosch Motorsport was formed to combine the unique abilities of two industry leaders, and offer the resulting technology to a new breed of racers. From import vs domestic drags, to time attack and airport racing, these high boost alcohol fueled engines exceed the capabilities of re-purposed production car parts, creating the need for a purpose built high flow motorsport injector.
Technology is nothing, until it provides solutions. In the case of the ID1300x and ID1700x, our customers made the needs of the market clear. Our job was to pay attention, and develop solutions that would meet those needs. Those needs, and the solutions are described below.
The complexity of modern engines often exceeds the capability of aftermarket ECU’s, necessitating the use of OE based hardware and strategies. Peak and Hold injectors, being decades old technology, are not supported by modern hardware, and so the X Series injectors are based on the high impedance Bosch EV-14 architecture.
While achieving high flow may seem easy, it poses significant challenges if the resulting dynamic response is to be useful. Much like the heads on your engine, the valve in the injector can only be opened so far before other problems arise. The challenge then becomes balancing flow against acceptable operating characteristics. In the case of the ID1300x, all available parameters were fine tuned to achieve the best results, with the ultimate flow limited to ≈ 1300 cc/min to avoid degrading the characteristics critical to operation in a motorsport environment. Namely, voltage sensitivity and pressure sensitivity described below, and low flow linearity and minimum fuel mass. At the time of its release, the ID1300x was the highest flowing all fuel compatible high impedance injector on the market. Racers being what they are – they quickly ran past the limits of the ID1300x, requiring even higher flow. The ID1700x came next, incorporating unique solutions to the challenges encountered during development of the ID1300x. Namely, the problem of achieving higher flow without degrading critical operating parameters. A study was conducted to quantify numerous modifications to the flow path, and resulted in a unique valve and seat assembly, parts of which are manufactured in house by Injector Dynamics. The end result is increased flow without the need to “open the valve” excessively. At the end of the nearly two year development process, eighteen different variations had been built and tested. Combined with numerous “tunable” parameters, more than 100 variations were tested, and the results speak for themselves, with the ID1700x being used on record setting cars in nearly every form of racing.
Broad Operating Range
If there is one requirement that stands out above the rest, it is the capacity for a broad operating range. Unlike OE applications, where an injector is designed for specific operating conditions, a motorsport offering requires that an injector serve everything from a twin turbo V8 on alcohol, to a 14,000 RPM Hayabusa engine on gasoline. This requirement is met by offering consistent operation across a wide pressure range, allowing the end user to change the effective flow rate. While most injectors will run static at high pressure on a test bench, few will perform well dynamically at those same pressures, and even fewer at high temperature with less than ideal battery voltage. In the case of the ID1300x, this challenge was met with the combination of a high current coil, optimization of numerous internal parameters, and an ultimate flow limitation of ≈ 1300 cc/min at 3 bar. The end result is an injector with impeccable manners, excellent pressure and voltage sensitivity, and a flow rate of ≈ 1900 cc/min at 6 bar.
In the case of the ID1700x, optimization of tunable parameters was not enough, and unique solutions were required. The ID1700x features a more powerful proprietary magnetic circuit, with parts manufactured in house by Injector Dynamics. The result is pressure and voltage sensitivity exceeding that of the ID1300x, requiring only 9 volts to open consistently at 6 bar, and a flow rate of ≈ 2640 cc/min at 7 bar. The ID1050x – the latest addition to the X Series – offers an even greater range, requiring only 8 volts for consistent operation at 8 bar, with an extended range of 1940 cc/min at 10 bar. While voltage requirements and ultimate pressure capability may seem little more than bragging rights, these capabilities become critical when trying to hot start a heat soaked engine with a high pressure fuel system and a lightweight racing battery.
(We know at least a few of you are nodding in agreement as you remember that long day on the dyno…)
Compatibility With all Automotive Fuels
Another key requirement is compatibility with all automotive fuels. From MTBE, to ethanol, the X Series are compatible with everything but dirt. Every dimensionally critical part inside of the X Series is made from corrosion resistant material, making them compatible with all fuels, and providing better long term consistency when used with corrosive fuels.
Injector Dynamics ID1700X Injectors
Full Race 4 Port MAC Boost Control Solenoid
Injector Dynamics ID2600 Fuel Injectors
3 Port Boost Control Solenoid (BCS) Fittings and Breather Filter
Torque Solution Exhaust Mount Kit for 9th Gen Honda Civic 2012-2015 (Including Si)
Hasport Honda Civic Si 9th gen 2012-2015 K24Z7 Rear Engine Mount
Barb Fittings and Breather Filter for 4 Port Boost Control Solenoid
Injector Dynamics ID1050X Injectors
3 Port MAC Boost Control Solenoid (BCS)
Full-Race 9th Gen Civic Si V-band Exhaust System
Full-Race Billet Vacuum / Boost Reference Manifold Block
Gold Heat Reflecting Film Self Adhesive 12" X 24"
For SHOP OWNERs
& KIT BUILDERs
Full-Race Motorsports is the most
trusted name in turbocharging.