Experts in Turbocharging since 2003

Build Now, Pay Later

The offer is valid for all orders within the USA. For other countries, the cost will be automatically calculated on checkout.

Free Shipping Over $249

Eligibility: 68 Million in the US. Also allows UK, Canadian and Australian Forces.
Included:
  • - Active Duty (currently serving in the Armed Forces)
  • - Veterans (formerly served in the Armed Forces)
  • - Dependents (spouse or child of above)
Military Discount

Turbo Speed Sensor Kit

SKU 179430

Turbo Speed Sensor Kit for Garrett and BorgWarner turbochargers. Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map.

This product is in stock and ready to ship!
$166.77
In stock
SKU
179430

Turbo Speed Sensor Kit for Garrett and BorgWarner turbochargers. Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map.

The Turbo Speed Sensor Kit is Critical for Proper Engine Operation

Turbo Speed sensors are critical in accurately identifying how fast the turbo is spinning and where your engine is operating on the compressor map. Traditionally, installing these sensors was difficult for the end-user—requiring complex machining at a compound angle to carefully hit the contour area of the wheel bore at the right angle. The latest generation BorgWarner and Garrett G turbos have this precision machining already done to every compressor cover. 

Note: We strongly recommend connecting this sensor to our Turbo Speed Gauge!

Speed Sensor Kit Includes

  • (1) Speed sensor, the frequency output
  • (1) Speed sensor hold-down bolt

Turbo Speed Sensor information and connection
Turbo speed sensor kit information

Turbo speed sensor kit

Notes for Installation

  • Garrett's turbos are plug-and-play without drilling
  • BorgWarner requires additional steps for installation

BorgWarner Installation Procedure

A 1/4″ Drill bit is all that's needed and the length/depth is very short. This hole allows the top of the sensor to come flush with the contour surface. The hole does not have to be precise as no sealing takes place in the small hole that the user just created. The hole must be deburred where it pierces into the wheel bore. The goal is to make sure that there are no sharp edges remaining in the wheel bore that the compressor can become caught on. The speed sensor is powered by a +5V supply and the return signal is a variable frequency square wave that has a maximum amplitude of 5V and has a 50% duty cycle.

    • 1. Remove compressor cover from turbo (CAREFULLY)
    • 2. Place cover on a table, with some kind of backing so that it won’t slide while being drilled
    • 3. Equip a hand drill with a 1/4” drill bit
    • 4. Drill out the bottom of the speed sensor bore while being careful not to nick the side walls of the bore where the speed sensor o-ring will seal.
    • 5. De-burr the hole where it protruded into the compressor wheel region.
    • 6. Lubricate the speed sensor o-ring
    • 7. Install the speed sensor into the bore and check for a good fit.
    • 8. Use a file on the mounting surface if the sensor needs to protrude further into the bore. The sensor tip should be nearly flush (within 0.5mm) with the edge of the hole.
    • 9. Tighten the speed sensor hold-down bolt.
    • 10. Re-install compressor cover on turbo and verify that the compressor wheel spins freely.

Turbo speed sensor kit

Turbo speed sensor kit

turbo speed sensor kit

turbo speed sensor kit turbo speed sensor kit

Click HERE to view a downloadable PDF file of how to install the Speed Sensor. If you have any questions about this product or its installation, contact us.

SKU

179430

WEIGHT

1.000000

BRAND

Full Race

Write A Review

similar products

For SHOP OWNERs
& KIT BUILDERs

Full-Race Motorsports is the most
trusted name in turbocharging.

Wholesale Inquiries
M-F: 8AM-4PM MST