BorgWarner 62mm S300SX FMW Turbo 8376 aka S362SX Billet
The 62mm S300SX FMW is BorgWarner Turbo Systems evolution of the proven Airwerks S300 turbocharger lineup. This turbo has been recently updated with their latest generation FMW 7-bladed Extended-Tip ‘billet’ compressor wheel w/ 62mm inducer & 83mm exducer in a 4″ inlet ported shroud compressor cover. This is paired with their proven 76mm inconel turbine wheel and tough 4340 steel shaft. Available in a variety of different turbine housings, made from HSM (HiSilMoly aka Hi-Silicon, Hi-Molybdenum) for increased strength at elevated temps, compared to traditional iron turbine housings. This turbo is recommended for use in quick spooling 450-650whp applications, and uses a severe-duty, 6-pad thrust bearing system to provide unprecedented levels of durability yet remains fully serviceable. Oil Cooled only (watercooling and BB CHRA not applicable).
English Racing Tuned Evo8, built 2.0L, 1.00 a/r
Mitsubishi EvoX from Andolfi Racing, Italy
2.2L stroker, Full Race T4 twin scroll kit, Motec M800, 272 cams, E85 fuel, Stock intercooler and pipes, S300SX FMW cupped tip at 2bar boost on 98RON pump fuel
Andolfi 2012 Subaru Impreza STI, 2.5L engine, complete Full Race T4 turbokit with intercooler and twinscroll FMW, 1000cc injector, at 21psi on 98RON pump fuel
2008 Subaru STi 2.5L on E85 with Full-Race twinscroll turbo kit:
2007 Subaru STi 2.5L w/ Full-Race twinscroll turbo kit
– comparison between BW S300SX FMW .91 a/r (Solid Lines) VS. GT4088R .95 a/r (dotted lines)
“the fact is the BW S300SX FMW is a ridiculously good turbo and absolutely unmatched for the price point. I’ve been trying different setups on my STI since I bought it new back in 2006… I’ve used a few of the FP bolt on turbos (regular green, HTA green, red), I used the ATP35R, Garrett 4088R, had a APS header up-pipe (four of them actually because they kept cracking), a Full-Race 1.5 scroll kit, and a Full-Race complete TS kit (what’s on the car now)… The BW S300SX FMW, by far has out performed any of my previous setups… I have spent a lot of time and money trying to make this car a respectable fast daily driver, and had all but given up before Geoff told me about this new BW turbo…This turbo just flat out kicks butt – good boost threshold, makes great power all they way up to my 8000rpms rev limiter, and the boost recover between shifts is just flat out instantaneous… I’m pretty confident that with E85, this turbo will do over 650whp with even more gains in the mid-range – I admittedly was surprised to see the boost threshold of a 35r and the power of a much larger turbo… On the dyno, we were hitting peak boost of ~29psi and then it would taper to ~27psi at redline, on the street it holds 30psi across the board.” Phil P
FULL RACE RECOMMENDS MODIFYING THE TURBINE HOUSING TO 3″ VBAND. This makes downpipe fitment identical to Garrett and Precision turbos, allowing you to swap between any t4 turbocharger with 3″ vband outlet and guarantees fitment with Full-Race twinscroll turbo kits and manifolds:
- Max warm oil pressure: 5 bar (73.5psi)
- Max cold oil pressure: 8 bar (118psi)
- When starting a fresh engine build or in extremely cold climates – oil pressure must reach 0.5bar (7.2psi) within 4 seconds maximum.
- Do not load the engine with full boost and WOT until full operating oil pressure is present
- Do not load the engine with full boost and WOT if any boost leaks are present (this can result in turbocharger overspeed)
For additional information and/or related questions, feel free to contact us.
- (866) Full-Race