Radium Engineering 2017+ Honda Civic Type-R Dual Catch Can Kit Fluid Lock
RADIUM ENGINEERING 2017+ HONDA CIVIC TYPE-R DUAL CATCH CAN KIT
Radium Engineering catch cans feature large 10AN ORB ports, a 4AN ORB drain port, 2-step oil separation baffling, and an O-ring sealed dipstick. This kit mount using factory holes and integrate perfectly with the surrounding components. These two oil catch cans (PCV side and CCV side) function completely independent of each other and are sold individually or together. They do NOT vent to atmosphere (VTA), thus are emissions and track legal. Closed loop systems remove the oil and sludge from the PCV gasses before it is routed to the engine to be burned. A closed loop system also promotes negative crankcase pressure for optimal performance. Furthermore, closed systems prevent unwanted oil vapors from entering the cabin. The dipsticks built into the catch cans allow easy inspection of accumulated fluid. No cutting, drilling or permanent modification to the vehicle is required.
The 20-0424 Catch Can Kit, PCV, Civic Type-R is for LHD vehicles. It secures to the RH firewall with no modifications required.This catch can runs inline with the PCV (positive crankcase ventilation) valve and retains it's factory function. When the intake manifold pressure is close to or greater than atmospheric pressure, the PCV "check" valve closes and, thus, this hose experiences no flow. Conversely, the PCV hose will experience "metered" vacuum when the engine is idling, steady state cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run. Note: No inline check valve is required since Radium catch cans are pressure sealed. This means a direct intake manifold connection is permitted.
The 20-0425 Catch Can Kit, CCV, Civic Type-R fits under the OEM engine cover with no modifications required.The catch can secures to the RH motor mount. If an aftermarket motor mount is used, minor modifications may be required. This catch can runs inline with the crankcase vent port. At low loads it experiences atmospheric pressure, but when the engine is at high load (WOT), this line will experience high flow out of the crankcase. This would normally lead to oil and sludge accumulation in the air filter intake pipe. Oil accumulation will occur in the intercooler which lowers the thermal efficiency properties of the heat exchanger and leads to decreased performance.The crankcase vent lines are routed over the engine and billet clamped to the turbo inlet pipe using temperature resistant metal tubes.
For the ultimate in engine protection, Radium recommends 20-0426 Dual Catch Can Kit, Civic Type-R.
This kit utilizes both the "CCV" and "PCV" catch can kits detailed above. It is designed for LHD vehicles.
Each kit features the following: -Anodized oil catch can with integrated condenser and dipstick-Anodized aluminum Honda FK8 specific mounting bracket-Anodized aluminum -AN adapter fittings and hose ends-Enough PCV hose for custom applications -Stainless steel mounting hardware
Hasport 2016+ Honda Civic Rear Motor Mount (Including 17+ FK8 Type R)
Honda Civic 2016+ 1.5T L15B7, 2017+ 2.0T K20C1, Civic Type-R FK8 | NGK Laser Iridium Spark Plugs (set of 4)
Turbosmart Honda Civic Type R FK8 and FK2 Kompact Supersonic BOV
2017+ Honda Civic FK8 Type R Radiator Upgrade
Honda FK8 Civic Type R PTP Lava Inlet Pipe Blanket
Honda Civic Type R FK8 and Accord 2.0T V-band Turbo Manifold
Honda FK8 Civic Type R PTP Lava Turbo Blanket
Garrett 2016+ Honda Civic 1.5T Si Performance Intercooler
Garrett G Series G25-660 Turbocharger
Hondata CTR MAF 500
Hondata FK8 Civic Type R Fuel System Upgrade
Radium Engineering Port Injection Fuel System Kit Honda Civic Type R K20C1
For SHOP OWNERs
& KIT BUILDERs
Full-Race Motorsports is the most
trusted name in turbocharging.